The refining industry has undergone many changes, from the methods of processing to the length of time that they operate their process units. These changes, along with the emergence of low sulfur fuel specifications, the requirement to process lower grade crude and the need to convert more bottom-of-the-barrel residuals, has put an extreme demand on isolation and control valves. Unreliable and unpredictable valves in emergency situations can cause enormous monetary losses and have devastating consequences for personnel. THINKTANK has responded to these challenges by developing a combination of diverse trim configurations and high quality coatings for use in high temperature, high pressure, erosive, corrosive, viscous and coking/asphaltene applications.
Reference List
The information of end-user:
Yulin Oil Refinery is located in the eastern suburbs of Jingbian County, Shaanxi Province, and was founded in 1993. In the initial stage of plant construction, the plant’s scale is only 150,000 tons/year of crude oil processing capacity and 70,000 tons/year of secondary processing capacity. Through more than ten years of development, the current installation’s primary crude oil processing capacity is 2 million tons/year, and the secondary processing capacity is 800,000 tons/year.
Problem:
Yulin Oil Refinery mainly processes crude oil in the Yulin area. It is estimated that the crude oil output in 2014 will be close to 5 million tons/year, which exceeds the refinery’s processing capacity. Therefore, the entire 5 million tons/year crude oil processing and supporting system transformation must be implemented as soon as possible to meet the rising demand for crude oil production in the Yulin area. And to cooperate with the country’s gasoline and diesel product upgrades, a 20,000Nm3/h hydrogen production device was designed in a combined device of 900,000 tons of gasoline and 2 million tons of diesel to ensure gasoline and diesel indicators meet the national level IV standards.
Design:
The design of the hydrogen production unit in the combined plant. This hydrogen production unit is designed for a reformed gas hydrogen extraction unit with 13000Nm3/h qualified hydrogen, with a design load of 60%~110%, and a conversion hydrogen production unit with a scale of 20000Nm3/h qualified hydrogen with a design load of 40%~110%.
Solution:
THINKTANK has provided 92 control valves for this device, used for raw gas pretreatment, conversion and medium temperature conversion, medium variable gas heat exchange and cooling, acid water recovery system, and PSA hydrogen purification unit. The products range includes globe type control valves, ball valves, high-performance butterfly valves, gate valves, etc.
This guide explains how to perform automatic setup on an Azbil Smart Valve Positioner 300 Series, including models AVP300, AVP301 and AVP302. The same basic procedure also applies to the corresponding remote-mounted AVP200 Series models. Before Auto-Setup Confirm that: Warning: Auto-setup moves the valve from fully closed to fully open.
This guide explains how to configure and automatically initialize a CHUANYI HVP3 smart valve positioner using the local three-button interface. Button Functions Button Function MODE Confirm a selection, switch operating modes, or enter and exit a special function UP Move upward through the menu, increase a value, or move the
This engineering guide explains 27 commonly used pneumatic control circuits for single-acting and double-acting valve actuators, including loss-of-air, loss-of-power, loss-of-signal, fast-stroking, anti-surge, turbine bypass, safety shut-off, and time-delay functions. Introduction A pneumatic actuator does not determine a control valve’s failure behavior by itself. The final action of the valve depends
This guide explains how to configure and automatically calibrate an ABB TZIDC or TZIDC-200 digital valve positioner using the local four-button interface. Button Functions Button Function ENTER Confirm a selection, start an action or save a setting MODE Select an operating mode, parameter group or parameter ▲ UP Move upward
This quick guide explains how to configure and automatically initialize a Siemens SIPART PS2 valve positioner using the local three-button interface. Before initialization, verify that the 2.YAGL setting matches the physical 33°/90° transmission ratio selector inside the positioner. Button Functions Button Function Operating Mode Button Select the operating mode, enter
This quick guide explains how to configure and perform automatic stroke calibration on a Flowserve Logix 3200MD+ digital valve positioner using its local DIP switches and control buttons. Button Functions Button Function ◄ BACK Return to the previous menu or cancel an operation ▲ UP Move upward through the menu
Avoid your inquiry is delay response, please enter your WhatsApp/Wechat/Skype along with the message, so we can contact you at the very first time.
We will reply you within 24 hours. If for urgent case, please add WhatsApp: +86 185 1656 9221, or WeChat: +86 199 2125 0077. or call +86 189 5813 8289 directly.
We will reply you within 24 hours. If for urgent case, please add WhatsApp: +86 199 2125 0077, or WeChat: +86 199 2125 0077. Or call +86 189 5813 8289 directly.
