thintank control valve manufacturer

Share optimized solutions, professional valve knowledge and industry news

What Is The Difference Between Pressure Control Valve and Flow Control Valve

The flow control valves are used for controlling and adjusting the fluid or gas flow through the system. The pressure control valve is used to regulate the pressure of a fluid passing through the pipe.
Table of Contents
    Add a header to begin generating the table of contents

    In fluid and gas control systems, pressure control valves and flow control valves are fundamental components designed to manage the movement and force of fluid or air. While they both contribute to the overall efficiency of a system, their roles and functionalities differ significantly.

    What Are Flow Control Valves?

    The flow control valves are used for controlling and adjusting the fluid or gas flow through the system.

    The flow control valve (FCV) is exactly the same except it gets its signals from a flow transmitter (FT). Just like the PT, an FT is basically a flow meter that is able to communicate with a related valve. Again, like the PCV, the FCV opens or closes based on the required flow and the signals it receives from the FT.

    closed loop control system
    closed-loop control system

    What Are Pressure Control Valves?

    The pressure control valve is used to regulate the pressure of a fluid passing through the pipe.

    A pressure control valve (PCV) opens and closes based on the setpoint predetermined by an engineer. This is usually controlled using a pressure transmitter (PT). The PT is basically an electronic pressure gauge that sends signals to the PCV and tells it whether or not there is enough pressure entering the equipment and the PCV opens or closes to compensate.

    control valves for boiler6
    control valves for boiler (globe valve cv)

    Ultimately, pressure and flow are not independent characteristics of fluid transport. You can’t change one without changing the other. But what you can do is monitor and control one, subjugating the other to follow. Pressure and flow control valves can look almost indistinguishable sometimes, except for the sensing mechanism, which is monitoring the variable you need in controlling.

    A pressure control valve opens and closes depending on the setpoint foreordained by a specialist. This is normally controlled utilizing a pressure transmitter. The flow control valve is actually the equivalent with the exception of it getting its signs from a flow transmitter. Much the same as the pressure transmitter, a flow transmitter is essentially a flow meter that can interact with a related valve.

    In essence, while pressure control valves safeguard system integrity by managing pressure, flow control valves ensure operational precision by controlling the rate of fluid or air flow. Both types of valves play crucial roles in diverse applications, contributing to the safety, efficiency, and sustainability of numerous systems.

    pressure control valve vs. flow control valve

    So the choice between a pressure control valve and a flow control valve depends on the specific application requirements, with pressure control valves used to maintain a constant pressure and flow control valves used to regulate the volume of fluid/gas passing through a system over a specific period.

    Pressure Control Valves V.S Pressure Regulators

    Does a pressure regulator affect flow?

    Indeed, a pressure regulator plays a significant role in managing the flow of a fluid or gas through a system, directly affecting the flow rate. This is particularly pertinent in systems that require low flow rates for optimal performance.

    Flow control at low flow rates can be a challenging endeavor. Precise control over the volume and speed of fluid or gas is required to ensure the system functions optimally. A great solution to this challenge is the use of an adjustable water flow restrictor. These devices enable the user to manually set the desired flow rate, maintaining the necessary pressure in the system.

    In addition to water systems, air systems, such as HVAC units, also require precise control of flow rates. The introduction of a digital airflow control valve into these systems brings about a level of accuracy and automation that was previously hard to achieve. These digital valves can monitor and adjust the flow of air in real-time, greatly enhancing the overall efficiency of the system.

    siemens calibration
    siemens calibration

    In fluid control systems, various components work together to regulate the flow and pressure of liquids and gases. To ensure optimal performance and efficiency, it is essential to understand the functions of these components, such as pressure flow controllers, back pressure regulators for slurries, downstream pressure controllers, e/p pressure regulators, pressure drop, valve body, flow path, and check valves.

    Pressure Flow Controller

    A pressure flow controller is a device that maintains a constant pressure in a system by automatically adjusting the flow rate. This helps to stabilize the pressure, ensuring consistent and reliable operation.

    Back Pressure Regulator for Slurries

    Designed to handle abrasive and corrosive materials, a back pressure regulator for slurries is a specialized type of pressure control valve. It maintains a desired upstream pressure by regulating the flow of slurries in processing plants, such as those found in the mining and chemical industries.

    Downstream Pressure Controllers

    Downstream pressure controllers are used to protect sensitive equipment from pressure fluctuations or to maintain a specific pressure in a process. These types of pressure control valves adjust the flow rate to maintain a constant pressure level downstream of the valve.

    E/P Pressure Regulator

    An e/p pressure regulator, or electro-pneumatic pressure regulator, uses an electrical input to control the pressure of compressed air or gas. This type of regulator is commonly found in industrial automation systems and provides precise pressure control for various applications.

    Pressure Drop

    Pressure drop refers to the decrease in pressure as a fluid flows through a system. This can be caused by factors such as friction, changes in flow path, or restrictions in the system. Understanding pressure drop is crucial for designing efficient fluid control systems and selecting the appropriate components.

    Valve Body

    The valve body is the primary component of a valve, housing its internal parts and providing a flow path for the fluid. The design of the valve body affects the valve’s performance, including its flow capacity and pressure drop characteristics.

    Flow Path

    The flow path is the route that a fluid takes as it moves through a system. It is determined by the arrangement of components, such as pipes, valves, and fittings. A well-designed flow path ensures smooth and efficient fluid flow, minimizing pressure drop and energy loss.

    Check Valve

    A check valve is a type of flow control valve that allows fluid to flow in one direction only, preventing reverse flow. Check valves are essential for protecting pumps and other equipment from damage caused by backflow, ensuring the safe and reliable operation of fluid systems.

    How to Adjust Pressure Control Valves?

    During the installation of pressure control valves, the engineers need to adjust control valves on-site. This is a significant step for commissioning. So we need to understand the various parts of the mechanical positioner and the working principle of the mechanical positioner. The following words will tell you all about the information on adjusting control valves.

    dn15 hls control valves
    flow control valve vs pressure control valve

    Selecting the right components is essential when choosing a pressure control system for any industrial or commercial application. One crucial element of such a system is the air flow control 6 feedback circuit, which ensures stable and accurate regulation of air flow. While it might be tempting to opt for a cheap flow control valve, it’s important to prioritize quality and reliability to avoid potential issues down the line.

    In many applications, a compressed air flow control valve is used to manage the flow of compressed air accurately and efficiently. This component can be found in systems that utilize a mode door actuator or a mode actuator to control the direction of air flow within an HVAC system. The integration of automatic climate control features further enhances the overall performance and user experience, providing a comfortable environment in various settings.

    Lastly, safety should never be overlooked when designing a pressure control system. A key component to consider is the HVAC B fuse, which protects the system from electrical faults and potential damage. By carefully selecting the right components and prioritizing quality, you can create an effective and reliable pressure control system that meets your specific requirements.

    Parts of Linear Mechanical Positioner for Globe Control Valve

    ep positioner parts
    ep positioner parts

    Principle of Linear E/P Positioner (ex. YT-1000L made by ROTORK/YTC)

    principle of linear valve positioner
    principle of linear valve positioner

    When INPUT SIGNAL is supplied to the positioner to open the valve, power is generated
    from ① the torque motor and pushes ② the flapper to the opposite side of ③ the nozzle.
    The gap between ③ the nozzle and ② the flapper becomes wider and from the inner part of ④
    the pilot left to ⑤ the spool, air inside ⑨ the chamber is exhausted through ③ the nozzle.
    Due to this effect ⑤ the spool moves to the right. Then, ⑦ the seat which was blocked by
    ⑧ the poppet pushes the poppet away and supplied pressure (air) goes through ⑦ the seat
    and OUT1 Port and enters into ⑩ the chamber of the actuator. Then ⑩ chamber’s pressure
    will increase and when there is enough pressure inside the chamber to push the actuator’s
    ⑪ spring, the actuator’s ⑫ stem will start to go down and through the feedback lever, the stem’s
    linear motion will be converted to span ⑭ lever’s rotary motion. This span ⑭ lever’s rotary
    motion will then once again rotate ⑮ the span and pull the spring. When the valve’s
    position reaches the given input signal, the span ⑯ spring’s pulling force and ① torque motor’s
    power will be balanced and move ② the flapper back to its original position to reduce the gap
    between ③ the nozzle. The amount of air being exhausted through ③ the nozzle will reduce
    and left to ⑤ the spool ⑨ the chamber pressure will increase again. ⑤ Spool will move
    back to its original position on the left and ⑧ the poppet will also move in the same direction
    blocking ⑦ the seat to stop the air coming into the ⑩ chamber through the SUPPLY. As a
    result, the actuator will stop operating and the positioner will return to its normal condition.

    Wiring Diagram of Valve Positioner

    wiring diagram of valve positioner
    wiring diagram of valve positioner

    Linear Positioner Installation

    Pneumatic globe type pressure control valve usually assembles linear positioner for diaphragm actuator or piston actuator.

    installation of electro pneumatic positioner
    installation of the electro-pneumatic positioner

    Step 1: Please refer to the above wiring diagram of the electro-pneumatic positioner to connect power cables to the terminal.

    Step 2: Check the positioner’s feedback lever position, it should be vertical to the valve stem at 50% of the valve stroke, same as the following picture.

    feedback lever for control valve
    The feedback lever for the control valve
    feedback lever is vertical
    feedback lever is vertical

    Step 3: Connect air power to the diaphragm actuator, usually, it’s 2.4 bar, then send a 4mA input signal to see if the valve is closed, and 20mA signal valve is fully open. (Failure position valve close, air to open) When we set zero and endpoints positions are set, then the rest of the position will be automatically calibrated. (25%, 50%, 75% position)

    acv in stock
    automatic control valve manufacturer(automatic air pressure control valve)

    If you want to know more about installation problems that happened on-site when you are commissioning or maintenance you can read the below post.

    pressure regulator vs flow regulator

    A pressure regulator and a flow regulator are both types of valves that control fluid flow, but they operate based on different principles. A pressure regulator is a valve that is designed to maintain a constant pressure downstream, regardless of fluctuations in the inlet pressure. It helps to regulate the pressure of a fluid as it passes through a system.

    On the other hand, a flow regulator is a valve that is designed to maintain a constant fluid flow rate, regardless of fluctuations in pressure. It helps to regulate the rate of flow of a fluid through a system.

    self operated pressure regulators
    pressure regulator
    steam control valves
    control flow regulators

    pressure regulator vs flow control valve

    The main difference between a pressure regulator and a flow control valve is their focus. Pressure regulators are focused on maintaining constant pressure, whereas flow control valves are focused on maintaining a constant flow rate. The choice between them depends on the specific requirements of the system in question, such as the desired flow rate or the maximum operating pressure.

    self operated pressure regulator for desalination
    self operated pressure regulator for desalination (water flow regulator)

    flow control vs pressure control

    Pressure control is achieved through the use of pressure control valves that can control fluid/gas pressure by restricting or increasing the flow rate. These valves help to maintain constant pressure inside the pipeline or system.

    The choice between flow and pressure control depends on the application objectives, system requirements, and industry standards. For example, if the objective is to maintain a steady flow rate, then flow control valves would be the best option. However, if the objective is to maintain constant pressure, then pressure control valves would be more appropriate.

    The pneumatic pressure relief valve symbol is widely recognized in technical schematics for controlling the pressure in fluid systems.

    Industrial Valve Symbols

    industrial valve symbols
    industrial valve symbols

    Valve Actuator Symbols

    valve actuator symbols
    valve actuator symbols

    Control Valve Symbols by Function

    control valve type
    control valve type

    Common Valve Symbols

    We provide various industrial valve symbols, including ball valves, gate valves, check valves, plug valves, diaphragm valves, safety valves, pressure regulators, solenoid valves, butterfly valves, and control valves. In case you will need it during the engineering fluid process. An air pressure regulating valve is an essential part of many industrial processes, as it maintains the desired pressure within pneumatic systems.

    common industrial valve symbols
    common industrial valve symbols

    Pressure Control Valve Symbol

    pressure control valve symbol
    pressure control valve symbol

    Self Actuated Pressure Control Valve Manufacturers

    Self-actuated pressure control valves are used to keep the adjustable set-point pressure within a certain range in tanks or processes. It doesn’t request any auxiliary energy to operate valves but by the medium energy itself. Automatic flow regulating valves are used in various industries to control the rate of flow in a fluid system automatically

    Since the self-acting pressure control valves do not need air supply or electric power to operate, so it’s kind of the most cost-effective pressure control valves to achieve a simple process of pressure control.

    self acting pressure regulators
    self actuated pressure control valves (directional control valve)

    Back pressure control valve definition refers to a device designed to maintain a set pressure upstream of itself at its inlet. Air pressure regulators are integral in many industrial and commercial applications, reducing input pressure to a steady and manageable output pressure. The output pressure refers to the pressure coming out of a system, device, or material, which is often regulated for optimal system performance. A filter in a fluid system serves to remove contaminants and particulates, promoting longer system life and improved performance.

    steam pressure reducing station
    steam pressure reducing station (adjustable hydraulic pressure regulator)

    Final Thoughts

    Learn from this post, you already know the difference between a flow control valve and a pressure control valve. For improved fluid control in your hydraulic system, you might want to buy a flow control valve from a reputable supplier. THINKTANK is a reliable control valve manufacturer who experiencing over 30 years in manufacturing control valves. So if you have any questions, just feel free to contact us. Also, you can read more posts about control valves below.

    Facebook
    Twitter
    LinkedIn
    Pinterest
    Print
    Will Don

    Will Don

    After earning my bachelor's degree in mechanical engineering from Zhejiang Normal University in 2008, l was fortunate enough to begin my career with Siemens, Fisher, and YTC, focusing on control valve accessories. Over the past dozen years, l've poured my heart and energy into understanding technology and fluid solutions for control valves.
    Now, as the marketing director for THINKTANK, a trusted branch of the Taiwan STONE valve group, I can't help butf eel proud of how far we've come. Our knowledge isn't just reaching professionals like engineer and valve distributors; it's also inspiring the next generation of automation college students.
    l genuinely hope you're enjoying our articles and finding them helpful.Your thoughts, questions, and feedback mean the world to me, so please don't hesitate to reach out to marketing[at]cncontrolvalve.com. Whether you're a seasoned expert or just curious about the field, I'm here to connect, share, and learn together.

    All Posts »

    I am the author of this article, and also the CEO and marketing director of THINKTANK, with 15 years of experience in the industrial valve industry. If you have any questions, you can contact me at any time.

    The Latest News
    control valve with dvc6200

    How to Calibration Fisher DVC6200 Positioner

    Based on our professional engineering control valve experience, we would detail the operational principles, technical specifications, and steps for troubleshooting or calibrating the Fisher DVC6200 ...
    Read More
    china electric butterfly valves

    Comprehensive Guide to China Electric Butterfly Valve Model

    This post is a complete guide to tell you the model of China electric butterfly valves mean.
    Read More
    figure 2

    Comprehensive Guide to Control Valve Installation and Commissioning

    This comprehensive guide to control valve installation and commissioning, informed by industry insights and the expertise of THINKTANK, elaborates on critical considerations for control valve ...
    Read More
    valve closing time

    Closing Time of Valve with Hydraulic Actuator

    When both pinch valves and knife gate valves use hydraulic actuators, the closing time calculation becomes a bit more standardized due to the similar ...
    Read More
    steam valves

    FAQs Steam Valves

    This post cover a wide range of topics about steam valves, their applications, design considerations, and specific uses in steam systems.
    Read More
    valve accessories selection tips

    Top Valve Accessories Selection Tips for Industry Professionals

    Dive into our professional tips of selection valve accessories to ensure your valve system is operating at its best, adhering to the highest performance and ...
    Read More
    axial valve

    TOP 10 Axial Flow Control Valves Manufacturers in The World 2024

    In the rapidly evolving industrial landscape, the demand for efficient and reliable axial flow control valves has surged, underscoring the critical role these components play ...
    Read More
    pressure unit conversion

    Pressure Unit Conversion Calculator

    Pressure Unit Conversion Calculator Pressure Converter Pressure Converter Input Unit: Pascal (Pa)BarPSI (Pound-force per square inch)Atmosphere (atm) Output Unit: Pascal (Pa)BarPSI (Pound-force per square inch)Atmosphere ...
    Read More
    cv to gpm

    CV to GPM Calculator

    Converts a valve’s CV (Flow Coefficient) to GPM (Gallons Per Minute), you would need to provide inputs for the CV value and the pressure drop ...
    Read More

    Contact Us

    With expertise in valves and rich experience in the oil&gas, chemical industry, textile mills, power plants, and sugar mills. THINKTANK has become the premier manufacturer of next-generation precision control valves.

    With a customer base that includes over 42 of the world’s leading engineering&contractors and international valve brands, THINKTANK Valves offers cost-effective valves that help our customers achieve automated process control without paying high prices.

    Why are more and more international valve brands choosing THINKTANK for OEM service?

    Brand is reputation, which not only requires high valve technology, but also great comercial support and fast response after-sales service and delivery time. They will not gamble their brand on an unknown product

    Get An Instant Quote

    Joy Preview

    Focused on Control Valves & Self-Operated Pressure Regulators For Over 30 Years

    A Good Partner Is A Lasting And Effective Investment

    Get An Instant Quote

    Direct to Control Valve Factory With Competitive Price & Reliable Quality

    Joy Preview
    Joy Preview

    Get An Instant Quote

    Just leave your name, email, and simple message or requirements, We will contact you within 1 hour.

    WhatsApp: +86 185 1656 9221

    Skype ID: sowell85

    Wechat ID: +86 199 2125 0077